Wika CPH6200 Manuel d'utilisateur Page 11
- Page / 100
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hand-Held Pressure Indicator
CPH6200-S1 / CPH6200-S2
GB
11221780.1.3 01/2009 GB/D/F/E
WIKA Operating Instructions Hand-Held Pressure Indicator 11
Menu Param. Setting Meaning
„Menu“
►
▲ or ▼
SEt
ConF
Set Configuration: Generic settings
Unit
mbar, bar, ... Unit: Unit of display
*, **
SL
oFF / on Sea-level correction: on or off
*, **
Alti
-200 ... +9999 Altitude: Input of altitude above sea-level [m] (only if on)
*, **
rAtE
Rate: Measuring rate (see chapter 2.3)
*
Slo Slow: Measuring rate (4 Hz filtered, low power consumption)
*
FASt Fast: Measuring rate, filtered (> 100 Hz)
*
P.dEt Peak detection: fast measuring rate, unfildered (> 100 Hz)
*
t.AVG
1 ... 120 Averaging interval in seconds, used by the averaging function off
oFF Averaging function deactivated
P.oFF
1 ... 120 Auto Power-Off delay in minutes. Device will automatically switch
itself off if, during this interval, no key is pressed, or there is no
serial communication.
oFF Auto Power-Off function inactive (continuous operation)
Out
oFF Function of the output: No output function, lowest power
consumption
SEr Output is serial interface
dAC Output is analogue output 0 ... 1 V
Adr.
01, 11 ... 91 Communicationsaddress of interface
dAC.
CH1, CH2 or
CH DIF
Choice of the input to be the source for the analogue output (if
Out = dAC)
dAC.0
eg. -5.00 ...
+5.00 mbar
Enter desired value at which the analogue output potential should
be 0 V (if Out = dAC)
dAC.1
eg. -5.00 ...
+5.00 mbar
Enter desired value at which the analogue output potential should
be 1 V (if Out = dAC)
SEt
CAL
Set Calibration: Adjustment of sensors
OFS.1
Sensordep.,
e.g. -5.00 ...
+5.00 mbar
The offset of sensor 1 will be displaced by this value to compen-
sate for deviations in the probe or in the measuring device.
OFF Zero displacement inactive (=0.0 °)
SCL.1
eg. -5.00 ...
+5.00 mbar
The measuring scale of sensor 1 will be changed by this factor
[%] to compensate deviations of temperature probe or measuring
device.
OFF Scale correction factor inactive (=0.000)
OFS.2
Sensordep.,
e.g. -5.00 ...
+5.00 mbar
The offset of sensor 2 will be displaced by this value to compen-
sate for deviations in the probe or in the measuring device.
OFF Zero dispacement inactive (=0.0°)
SCL.2
eg. -5.00 ...
+5.00 mbar
The measuring scale of sensor 2 will be changed by this factor
[%] to compensate deviations of temperature probe or measuring
device.
OFF Scale correction factor inactive (=0.000)
- CPH6200-S1 1
- CPH6200-S2 1
- Information 2
- Warning! 2
- Contents 3
- 1. General 4
- Hand-Held Pressure Indicator 10
- CPH6200-S1 / CPH6200-S2 10
- Main Menu 10
- 2. Configuration 12
- 3. Operation of logger 17
- 4. The serial interface 21
- 5. Available pressure sensors 21
- 6. Fault and system messages 22
- 7. Calibration services 23
- 8. Specifications 23
- 9. Accessories 25
- Hand-Held Druckmessgerät 26
- 1. Allgemeines 28
- 2. Konfigurieren des Gerätes 36
- 4. Die serielle Schnittstelle 45
- 5. Verfügbare Drucksensoren 45
- 8. Technische Daten 47
- 9. Zubehör 49
- Sommaire 51
- 1. Généralités 52
- Valeurs Signification 59
- 4. L'interface sérielle 69
- 9. Accessoires 73
- Manómetro portátil 74
- Contenido 75
- 1. Información general 76
- 2. Configuración del aparato 84
- 4. Puerto serie 93
- 8. Datos técnicos 95
- 9. Accesorios 97
- North America 99
- South America 100
- Africa / Middle East 100
- Australia 100
Produits connexes et manuels pour Instruments de mesure Wika CPH6200
(132 pages)
(160 pages)MicroNet Commutateurs de réseau manuels d'utilisation
La liste de MicroNet Commutateurs de réseau produits contient 11 manuels d'utilisation pour les modèles 10. Tous les guides d'utilisation en format pdf peuvent être téléchargés ou consultés en ligne.
Commentaires sur ces manuels