Wika TC12-M Manuel d'utilisateur Page 28
- Page / 72
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
GB
8. Safety-related instructions for the dierent variants
14083458.01 09/2013 GB/D
WIKA operating instructions models TR12, TC12 (Ex i)28
8. Safety-related instructions for the dierent variants
8.1 Variant 1:
ATEX/IECEx Ex d housings or connection heads (with connection terminals, without
transmitter). Evaluation of the resistance or the thermoelectric potential between electronics
outside of the hazardous area.
Use in zone 1, marking II 2G Ex ia IIC T1-T6 Gb
The housing or the connection head is in zone 1 (or zone 2). The sensor is located in
zone 1.
Use with a thermowell at the partition to zone 0, marking II 1/2G Ex ia IIC T1-T6 Ga/Gb
The housing or the connection head is in zone 1 (or zone 2). The sensor is within a
thermowell (min. wall thickness 1 mm) which extends into zone 0 via a process connection.
The thermometer should therefore be operated with a power-limiting circuit.
Powering with Ex ia electrical circuit fullls these conditions. The responsibility rests with the
operator.
Temperature class classication, ambient temperatures
For all WIKA connection heads, the following ambient temperature range applies:
(-50)
1)
-40 … +80 °C
1) The value in brackets applies only for specic low-temperature designs.
The permissible ambient temperatures for third-party products can be seen from the
relevant approvals and/or data sheets.
A heating in the connection head does not occur with varient 1. However, an impermissible
heat reux from the process which can exceed the operating temperature of the housing or
the temperature class, must be prevented through suitable heat insulation or a suitably long
neck tube.
8.2 Variant 2:
ATEX/IECEX Ex ia housing or connection head with built-in head-mounted transmitter.
The evaluation is made via a current (4 … 20 mA), voltage (2 … 10 V) or eld bus signal,
which is generated from a head-mounted transmitter.
Use in zone 1, marking II 2G Ex ia IIC T1-T6 Gb
The housing or the connection head is in zone 1 (or zone 2). The sensor is located in
zone 1.
Use with a thermowell at the partition to zone 0, marking II 1/2G Ex ia IIC T1-T6 Ga/Gb
The housing or the connection head is in zone 1 (or zone 2). The sensor is within a
thermowell (min. wall thickness 1 mm) which extends into zone 0 via a process connection.
- Operating instructions 1
- Betriebsanleitung 1
- 14083458.01 09/2013 GB/D 2
- Contents 3
- 1. General information 4
- 2. Safety 5
- 3. Specications 10
- 4. Design and function 12
- 6. Commissioning, operation 17
- (Europe) 22
- Option: with built-in 27
- Sensor type RTD TC 31
- Measuring insert diameter 31
- 10. Maintenance and cleaning 32
- 11. Faults 33
- 1. Allgemeines 38
- 2. Sicherheit 39
- TR12-M-AICZ 42
- TC12-B-AICZ 42
- 3. Technische Daten 43
- 4. Aufbau und Funktion 46
- 6. Inbetriebnahme, Betrieb 51
- Option: mit eingebautem 61
- Transmitter z. B. T32 61
- Schutzrohrspitze 64
- Sensortyp RTD TC 65
- Messeinsatzdurchmesser 65
- 10. Wartung und Reinigung 66
- 11. Störungen 67
- WIKA global 70
- North America 71
- Latin America 71
- Africa / Middle East 72
Produits connexes et manuels pour Instruments de mesure Wika TC12-M
(72 pages)
(40 pages)
(48 pages)Rugged-ridge Upper Door Kit, Rear, Black, 07-14 Jeep 4-Door Wra podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Do samochodu Rugged-ridge Upper Door Kit, Rear, Black, 07-14 Jeep 4-Door Wra.
Dostarczamy 1 pdf podręczników Rugged-ridge Upper Door Kit, Rear, Black, 07-14 Jeep 4-Door Wra do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Commentaires sur ces manuels